to mau2x (the final round)

Solving the third and bottom layer

Now that we’re done with the top, first and 2^nd layer we are going to fix the third layer and bottom layer, the best thing here is that fixing the third layer is also fixing the bottom layer altogether, just like the first and the top layer, ok so much for the talking.. let’s start with the procedures….

Note that our top layer is yellow and our bottom layer is white; let’s call it the original config. Why config? I don’t know I just feel like calling it so… so let’s start...

1. by now your cube should look something like this…

2. now turn the cube upside down making the white our top layer and yellow our bottom layer. by now your cube should look at least one of these. . .

now we are going to form a nine o'clock figure using the white tiles (if there is already a nine o'clock figure ignore this steps and proceed to step 10, but read steps 3 to 9 first to know the details, ok?).

3. face the blue side, or any side as long as the straight white tiles are pointing directly to you, like this...










(from now on we will use the following convention TL for top layer, BL for bottom layer, and so on, refer to the figure below)













4. turn RSL downwards
5. turn TL to the right
6. turn FL CCW
7. turn TL to the left
8. turn FL CW
9. turn RSL upwards

by now you should have a 9 o'clock white tiles figure... like this...










10. after having a nine o'clock figure, we going to from a cross white tiles figure.. to from a cross just repeat steps 4 to 9 ( if there is already a cross figure proceed to next step)..

by now your cube should like like this...










11. turn your cube back to the original config (TL - yellow)
12. find one tile on the on the center of the 3rd layer that has the same color to the center of 2nd layer. like this...

12. face the side where the center of the 3rd layer has the same color to the center of 2nd layer (for this case face the blue side).

13. turn RSL downwards
14. turn the 3rd layer to the right twice
15. turn RSL upwards
16. turn the 3rd layer to the right once.
17. turn RSL downwards
18. turn the 3rd layer to the right once.
19. turn the RSL upwards

check if all the center of the 3rd layer correspond to all the colors of the center to the 2nd layer. if not, repeat steps 13 to 19 facing the same side in step 12.

from now on we will call steps 13 to 14 "down right right" ok?

by now your cube should look something like this...



there are cases where after forming the cross figure you can't locate only one color on center of the 3rd layer which corresponds to the color of the center of the 2nd layer, instead naay duha ka color miski unsa-on og tuyok sa 3rd layer duha jud kabouk ang masakto.... like this...

____________________________________________________________________
parehas ani, ang duha ka side ok na ang duha nag baylo (ayaw ni i.comfuse sa last step ok? situation ra ni after pag form og cross instead nga isa nlng ka color parehas sa figure ubos sa step 12, ang nahitabo two ka color ang sakto miski unsaon pag tuyok.. so imong buhaton...

1.1.1. face either side nga wla nag correspond ang color sa center sa second og third layer, make sure nga isa sa nasakto nga color sa 2nd og 3rd layer naka position sa LSL.

1.1.2. then do the "down right right" move
1.1.3. after the "down right right" check if all center of the 2nd and 3rd layer correspond with each other by turning the 3rd layer either to the left or right... gikapoy nakog english oy!!! pero wla man puy nag sugo sko nga mag english ko...
____________________________________________________________________

now let's go back...

after all the centers of the second and third layer correspond with each other (meaning naa na clay mutual understanding, letse kau nga mga tiles mag M.U.2x) we're ground to arrange the corners of the third layer, this is last and final step to complete the cube.. yeahey!!!

20. first look for a corner of the 3rd layer where the three tiles are compatible with the colors of the bigger corner.. like this...

take note that white is still your bottom layer and yellow's still your top layer. this is just an illustration, got it?...








21. hold the cube such that the corner of the 3rd layer on target (meaning kanang white-blue-orange nga corner) is on the right side layer...
22. do the "down right right" move

steps 23 to 29 we will call this the "counter" move...

23. turn LSL downwards
24. turn the 3rd layer to the right twice
25. turn LSL upwards
26. turn the 3rd layer to the right once.
27. turn LSL downwards
28. turn the 3rd layer to the right once.
29. turn the LSL upwards

check if the corner of the 3rd layer and the bigger corner is already arranged, if not do the "down right right" and the "counter" move once more until the corners are arranged.

do the same move for the rest of the corners, until the cube is completed and your done...

bare in mind that the target corner should always be on the right side layer, meaning kung ma arrange na ang isa ka cornera ang sunod nga corner i.arrange ang naa sa iyang right side... naay case nga ang 3 ka color sa corner og ang bigger corner dili mag compatible.. naay steps ani pero tym na man so i.txt nlng in case maka tagbo ka ani nga problema, im sure maka tagbo ka ani... txt lang,...